The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. Left or right-side fitment. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

View/Change Diagram

911 1970-73 - Front Axle/Steering	911 1974-77 - Front Axle/Steering
911 1978-83 - Front Axle/Steering	911 1984-86 - Front Axle/Steering
911 1987-89 - Front Axle/Steering	912 1965-69 - Front Axle/Steering
912 1965-69 - Front Axle/Steering	914 1970-76 - Front Axle/Steering
911 1965-69 - Front Axle/Steering	911 1965-69 - Front Axle/Steering

The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. Sold individually. Left or right side fitment. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Lowering your car without a bump steer kit effectively pulls the steering out of alignment and requires constant steering adjustments that make the car difficult to control. This adjustable bump steer kit will fully compensate to return the steering rack / geometry back to pre-lowered specifications. Our bump steer kit is manufactured to the highest of German standards to ensure the quality, performance and reliability you expect from your Porsche. Features: alloy steel, sealed spherical rod end 14 mm tapered wedge for secure fitment inside the steering arm made for lowering below 30 mm (1.18 inches) / raised spindles allows tie rods to be adjusted downwards no binding throughout suspension travel range finishe...(choose a part on the right to read more)

General Fitment

The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. Left or right-side fitment. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

View/Change Diagram

911 1970-73 - Front Axle/Steering	911 1974-77 - Front Axle/Steering
911 1978-83 - Front Axle/Steering	911 1984-86 - Front Axle/Steering
911 1987-89 - Front Axle/Steering	912 1965-69 - Front Axle/Steering
912 1965-69 - Front Axle/Steering	914 1970-76 - Front Axle/Steering
911 1965-69 - Front Axle/Steering	911 1965-69 - Front Axle/Steering

The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. Quality European aftermarket replacement designed to perform like the original. Sold individually. Left or right-side fitment. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)

The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use.

Why not replace them with stock rubber bushings? Most 911 owners today, especially those of us who take our cars to the track, have equipped our Porsches with tires much wider and stickier than stock, which allows higher g-forces to be achieved in cornering and braking. During that type of hard driving, rubber suspension bushings are compressed and flexed by the extreme loads being put on them, defeating your car's finely...(choose a part on the right to read more)

General Fitment

The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use.

Why not replace them with stock rubber bushings? Most 911 owners today, especially those of us who take our cars to the track, have equipped our Porsches with tires much wider and stickier than stock, which allows higher g-forces to be achieved in cornering and braking. During that type of hard driving, rubber suspension bushings are compressed and flexed by the extreme loads being put on them, defeating your car's finely...(choose a part on the right to read more)

General Fitment

The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use.

Why not replace them with stock rubber bushings? Most 911 owners today, especially those of us who take our cars to the track, have equipped our Porsches with tires much wider and stickier than stock, which allows higher g-forces to be achieved in cornering and braking. During that type of hard driving, rubber suspension bushings are compressed and flexed by the extreme loads being put on them, defeating your car's finely...(choose a part on the right to read more)

General Fitment

Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)

Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)